| 1. Portable 60 kV IEC tester | 60 kV AC | IEC 60156 procedure; voltage rise is set to the method’s specified rate, commonly 2.0 kV/s. | Uses the specified IEC test cell and electrode geometry; a 2.5 mm gap is common for IEC 60156 testing. | Usually about 300–500 mL, depending on the cell. | Basic automatic voltage ramp and breakdown detection; results may be recorded manually or stored internally. | Field checks and routine testing where portability and a straightforward IEC procedure are priorities. |
| 2. Bench-top 80 kV IEC tester | 80 kV AC | IEC 60156 procedure; typically configured for a 2.0 kV/s voltage rise. | IEC-compatible cell and electrodes, with the required electrode gap set and checked before testing. | Usually about 300–500 mL, depending on the cell. | Automatic test sequence, breakdown recognition, and storage of test results are commonly available. | Routine transformer-oil testing in maintenance workshops and utility laboratories. |
| 3. Bench-top 100 kV IEC tester | 100 kV AC | IEC 60156 procedure; commonly uses a 2.0 kV/s rise rate when configured for that method. | IEC-compatible cell and electrodes; test geometry must match the selected procedure. | Usually about 300–500 mL, depending on the cell. | Automatic sequence and result storage; some configurations provide report export. | Laboratories that need additional voltage headroom for a broader range of insulating-liquid tests. |
| 4. Multi-method 80 kV tester | 80 kV AC | May support selectable methods such as IEC 60156, ASTM D1816, and ASTM D877. Their voltage-rise rates differ; commonly specified rates are 2.0 kV/s for IEC 60156, 0.5 kV/s for ASTM D1816, and 3.0 kV/s for ASTM D877. | Requires the appropriate cell, electrodes, and spacing for each selected method; one cell setup is not suitable for every method. | Typically about 300–500 mL; method and cell requirements determine the actual amount. | Method selection and automatic test sequences are commonly available; confirm that settings match the current standard. | Service providers and laboratories testing to more than one recognized procedure. |
| 5. Multi-method 100 kV laboratory tester | 100 kV AC | Can be configured for multiple procedures, including IEC 60156 and applicable ASTM methods; ramp rate must be selected for the chosen procedure. | Uses method-specific cells and electrodes. Electrode gap and geometry should be verified for each test method. | Typically about 300–500 mL, depending on the method and test cell. | Often offers programmable sequences, result memory, and data export; available features vary by configuration. | Central laboratories handling varied methods, test programs, or higher-voltage requirements. |
| 6. Manual-control 80 kV tester | 80 kV AC | Can be used for a supported procedure when the operator sets the correct voltage-rise rate and follows the method. | Method-specific cell and electrode setup must be installed and checked by the operator. | Usually about 300–500 mL, depending on the cell. | Operator-controlled testing; automated breakdown protection may be present, but sequence and record features are more limited. | Basic laboratory work where operators prefer direct control and can carefully follow the test procedure. |
| 7. Automated 100 kV laboratory tester | 100 kV AC | Programmable for supported procedures; each test must use the correct method-specific ramp rate and sequence. | Requires the correct cell and electrode arrangement for the selected standard; correct spacing and clean, dry equipment are essential. | Typically about 300–500 mL, depending on the test cell and procedure. | May provide automated multi-breakdown sequences, data storage, and report export; verify software and traceability features. | High-throughput laboratories seeking consistent sequences and electronic result records. |
| Comparison note: These are representative tester configurations, not specifications for individual products. Voltage capacity, supported standards, test-cell geometry, ramp-rate settings, sample volume, and record features vary by instrument. Confirm the current edition of the applicable test method and the instrument documentation before testing. |